HAVE YOU CONSIDERED INCINERATION?
DISPOSING OF YOUR WASTE PAPER AND CARDBOARD CAN BE AN EXPENSIVE BUSINESS.
WHY NOT BURN YOUR WASTE ON YOUR OWN SITE?
WE HAVE THE SOLUTION TO YOUR WASTE PROBLEMS.
THE RIGHT INCINERATOR FOR YOU - The MKI is 5 cu. ft.
and the MKII is 10 cu.ft. If you have little waste or you can take your
time to burn small quantities the MKI is for you. If you have large amounts
or wish to burn quickly the MKII would suit you better. A good guide is
that the MKI is capable of burning 25 kgs per hour and the MKII no more
than 40 kgs per hour The units, therefore, comply with the rules of the
Environmental Protection Act. Assess the weight of your waste, and time
available, and choose the model to suit your needs.
|
|
|
SPECIFICATION
|
MKI |
MKII |
MKIII |
DIAMETER
HEIGHT
WEIGHT
|
30½"
30½"
206 kgs |
DIAMETER
HEIGHT
WEIGHT |
30½"
53½"
343 kgs |
DIAMETER
HEIGHT
WEIGHT |
30½"
79½"
492 kgs |
PICTURE MISSING
SITING
1) Site a minimum of 6 metres from any building or trees.
2) Do not place in an area of great air turbulence.
3) When burning, the lid will become very hot so consider the safety
aspects.
4) Find a site which is level and firm.
PARTS LIST |
MK I |
MK II |
MK III |
|
Base Plate |
1
|
1
|
1
|
|
Side Sections Plain |
2
|
4
|
6
|
|
Side Sections with Cut-Out |
1
|
2
|
3
|
|
Stainless Steel Lid |
1
|
1
|
1
|
|
Strap Thin |
-
|
1
|
2
|
|
Strap Thick |
1
|
3
|
2
|
|
Wingnut and Bolt |
1
|
3
|
2
|
|
Firebars with Air Cone Attached |
1
|
1
|
1
|
|
2 Part Insert |
1 set
|
1 set
|
1 set
|
|
Rake |
1
|
1
|
1
|
|
Ash Out Door |
1
|
1
|
1
|
|
Mild Steel Cladding |
-
|
-
|
1
|
INSTALLATION PROCEDURE
a) |
Place base tile on level ground and erect 2 plain side sections
and 1 cut out section around it ensuring that the interlocking tongue
and groove joints fit snug. The cut out is for ash rake out so the
area is to the bottom.
|
b) |
Distance the thin strap approximately midway and fasten ends together
with butterfly nut and bolt.Hang the ash out door from this strap
and move the strap until the ash out door covers the corresponding
opening. |
c) |
Set the 2 part insert within leaving the cut out area free. |
d) |
Place the firebars with the cone on top of these insert bricks.
If you are constructing the MK I your job is finished, simply place
the lid on top. |
MK II ONLY
e) |
Set the top side sections in place with the cut out uppermost. This
cut out will help when loading. |
f) |
Fasten the wider strap around the seam line of the upper and lower
sections with equal overlaps and tighten with wing nut and bolt. |
g) |
Fasten the thin strap midway around the upper sections and put lid
in place. |
MK III ONLY
h) |
Set 3rd level side sections in place with cut out at bottom. |
i) |
Wrap around mild steel cladding with hinged door and put lid in
place. |
|
|
|